#HARMONIC BALANCER INSTALLATION TOOL HOW TO#
#HARMONIC BALANCER INSTALLATION TOOL INSTALL#
#HARMONIC BALANCER INSTALLATION TOOL DRIVER#

Installation is equally easy with the right tool. ItвЂ™s simple and effective, and creates no damage to the damper or crankshaft. The magic of threads goes to work, and the damper eases off the end of the crank. Using a 1-1/8-inch socket or wrench (socket size depends upon the tool - IвЂ™m referencing my old Kent Moore puller here), you simply tighten the screw. The puller usually includes a large diameter, fine-thread screw that runs through the center of the plate. Typically, the plate attaches to the same bolt pattern as the crank pulley. A really good example is Summit RacingвЂ™s removal/install tool, (SUM-G1025).ДЄ good damper removal tool is simple to use and extremely effective.ДЇor the most part, you simply bolt a plate to the face of the damper.

I have a couple of examples including several vintage GM Kent Moore service jobs in my tool box. The good news, and the real solution, is to use the appropriate tools. ThereвЂ™s a really good chance you can destroy the threads in the crank snout doing that. You can damage the damper easily.Дitto if you use a bolt to try and pull it on by way of the crank threads.

#HARMONIC BALANCER INSTALLATION TOOL DRIVER#

How about installing one? A block of wood and the biggest hammer in your tool box, or even a dedicated pulley driver arenвЂ™t the answers either. In fact, most aftermarket harmonic damper manufacturers explicitly note that the use of a three-jaw puller is forbidden with their respective products. You might get away with yanking one off with a common three-jaw puller, but you can bet your boots the damper will be damaged, if not ruined.

#HARMONIC BALANCER INSTALLATION TOOL INSTALL#

The factory balancer bolt is a single-use fastener, so you will need to get a new factory bolt or better still, an ARP balancer bolt that is stronger and reusable.Harmonic dampers are typically press-fit and next-to-impossible to properly remove and install without the right tools. Using the balancer wrench and breaker bar to keep the crank from rotating, install the new balancer bolt to proper torque. The balancer wrench can be used here to stop crankshaft movement. To reinstall the balancer, thread the installation tool into the threaded bore of the crankshaft snout by hand until seated.

DonвЂ™t use an impact gun for this procedure as excessive force can damage the cast balancer. Once tension is established against the brace rod, use a ratchet to remove the balancer from the crankshaft.

The jaws align with the relief areas cast into the LS balancer, and apply even tension against the crank snout as the tool is tightened and the balancer removed. You want the brace rod to extend at least an inch beyond the pulley hub. The crankshaft bore seat is deep in the crank snout. The tool comes with four different length rods-choose the rod that works with your application. The three jaw puller uses a brace rod that fits in the tool and the inner bore of the crank snout. With the balancer braced and unable to turn, remove the balancer bolt with a ratchet or impact wrench. Make sure you donвЂ™t brace against brake lines, fluid lines, or other vulnerable parts. A 1/2-inch breaker bar is used to brace the balancer against a frame rail or suspension component. The balancer wrench fits between the lower spokes of the balancer. The Summit Racing LS harmonic balancer installer and removal kit comes with a balancer installation tool, three jaw puller, and a balancer wrench. Using the Summit Racing LS balancer tool is easy-and works much better than that hammer you thought about using. The wrench also comes in handy to rotate the engine during assembly or cam degreeing. The tool comes with a three-jaw puller plate with brace rods balancer installation tool and a balancer wrench with heat-treated 4140 chromoly studs.

#HARMONIC BALANCER INSTALLATION TOOL HOW TO#

But there is one thing that everyone should be taught, and thatвЂ™s how to use the right tools to install and remove a harmonic balancer.ДЇor example, Summit Racing makes a dandy harmonic balancer puller and installer tool just for GM LS engines. Remember when your mom told you not to run through the house with scissors or to stop sticking that screwdriver in the electric outlet? OK, maybe that was us.

Harmonic balancer installation tool